Electrical Guides

Carbon Monoxide Detector Beeping or Chirping: What It Means

A beeping carbon monoxide detector can mean three very different things. It might be warning you about CO in the air right now. It might just need a battery. Or it might be telling you the alarm itself is worn out or broken.

Key takeaway

The sound pattern tells you which one. But before anything else, start here.

First: if it’s a loud, repeating alarm, get out

Carbon monoxide has no smell or color. You can’t check for it yourself, so don’t try.

If your detector is sounding a loud pattern of beeps that keeps repeating (on most First Alert and Kidde CO alarms, that’s 4 beeps, a pause, then 4 beeps again), or a voice alarm is saying “carbon monoxide”:

  1. 1
    Get everyone out of the house to fresh air, pets included.
  2. 2
    Call 911 from outside.
  3. 3
    Stay outside until emergency responders tell you it’s safe to go back in.

Don’t open windows and wait to see if it stops. Don’t press the silence button and go back to bed. If you’re not sure what kind of beep you’re hearing, treat it as an alarm and leave.

Two-story house at night with lights on and people gathered outside on the lawn
If a CO alarm sounds, get everyone outside into fresh air, then call 911.

Symptoms of CO poisoning to take seriously

Because CO can’t be seen or smelled, your body may notice it before you do. According to the CDC, the most common symptoms are headache, dizziness, weakness, upset stomach, vomiting, chest pain, and confusion. They’re often described as flu-like, and the CPSC notes they’re easy to mistake for the flu, just without the fever.

If anyone in the house has these symptoms, whether or not the alarm is sounding, the CPSC says to get outside to fresh air right away, call the fire department or 911, and tell a doctor you suspect CO. People who are asleep can be overcome before they notice any symptoms at all.

Where carbon monoxide comes from at home

CO comes from burning fuel. The CPSC and CDC list common home sources, including:

  • Gas furnaces and room heaters
  • Gas water heaters
  • Gas stoves and ranges
  • Fireplaces and wood stoves
  • Portable generators
  • A car left running in an attached garage, even with the door open

If an alarm points to one of these, the fix belongs with that appliance’s specialist, such as an HVAC or gas appliance technician, not an electrician. The CPSC advises not using a suspect appliance until trained personnel have serviced it. If you run a generator during an outage, our post on preparing for North Georgia wind and power outages covers keeping backup power safe.

Where CO alarms should go

The CPSC recommends CO alarms on every level of the home and outside sleeping areas, with battery power or battery backup. Interconnected alarms are best, because when one sounds, they all sound. Keep alarms clear of furniture and curtains, and follow the manufacturer’s placement instructions.

Alarm, chirp, or trouble signal: how to tell them apart

Once you know it isn’t an alarm, listen for the pattern. The patterns below come from First Alert and Kidde’s own support pages. Brands and models differ, so confirm against your manual (more on that below).

Emergency

The CO alarm: loud, repeating groups of beeps

  • First Alert: 4 beeps and a pause, repeating. First Alert calls this an emergency: move to fresh air and call 911.
  • Kidde: four short beeps, about five seconds of silence, then four short beeps again.

This is the one that means get out. It’s loud, it keeps going, and it doesn’t sound like a single chirp.

Battery

Low battery: one chirp about every minute

  • First Alert: one chirp per minute means low battery.
  • Kidde: a chirp about once every 60 seconds can mean the batteries need replacing.

Replace the battery with the type your manual lists, then test the alarm with its test button.

Replace

End of life: the alarm needs replacing

CO sensors wear out. When they do, the alarm tells you with its own chirp pattern, and a new battery won’t stop it.

  • First Alert: 5 chirps every minute means end of life. Replace the alarm.
  • Kidde: about seven years after it’s first powered up, a Kidde CO alarm chirps every 30 seconds. Kidde says it can no longer detect CO in this mode, so replace it right away.
Malfunction

Error or malfunction: the alarm isn’t working right

  • First Alert: 3 chirps every minute is a malfunction warning. The alarm needs to be replaced.
  • Kidde: chirping every 30 seconds can also point to a malfunction, and models with a screen may show “ERR.” Kidde lists its product support line as 1-800-880-6788.

Here’s the catch: on Kidde alarms, end of life and malfunction can sound similar. Either way, the alarm isn’t protecting you, so it needs attention now, not next weekend.

Close-up of a round white smoke detector
Your alarm’s manual or back label explains what each beep pattern means.

Quick reference

Loud groups of 4 beeps, repeatingCO alarmGet out, call 911
1 chirp about every minuteLow batteryReplace battery, then test
3 chirps every minute (First Alert)MalfunctionReplace the alarm
5 chirps every minute (First Alert)End of lifeReplace the alarm
Chirp every 30 seconds (Kidde)End of life or malfunctionCheck manual, replace the alarm

Patterns vary by model. Your manual has the final word.

How to find your model and check the manual

  1. 1
    Take the alarm down (it usually twists off its base) and look at the label on the back.
  2. 2
    Write down the brand, model number, and the manufacture or “replace by” date. Many alarms print the date right on the label.
  3. 3
    Find the manual. If you’ve lost the paper copy, search the model number on the manufacturer’s website. First Alert and Kidde both post manuals and beep-pattern guides on their support pages.
  4. 4
    Match what you heard to the chart in the manual, and follow its steps.

If the alarm is past its replace-by date, replace it even if it seems fine.

Round detector and alarm unit mounted on a white ceiling
The model number and date are printed on the back of the detector, so you’ll need to take it down to read them.

Check your model: CPSC warning on JZA-540COM alarms

On October 29, 2026, the CPSC warned consumers to stop using JuzhiAnn, Yfwsrecinoe and JAEHSKA combination smoke and CO alarms, model JZA-540COM, because they can fail to alarm in smoke or fire. That is a separate problem from beeping, but it’s worth checking your model number while the alarm is in your hand. If it matches, the CPSC warning says to stop using it, dispose of it, and install working alarms.

FAQ

Why is my carbon monoxide detector beeping when there’s no CO?+

Most often it’s a low battery, an end-of-life signal, or a malfunction warning. A single chirp on a timer is usually not an alarm. A loud, repeating pattern is. If you can’t tell which, leave the house and call 911.

Will a new battery stop an end-of-life chirp?+

No. End of life means the sensor is worn out, and the alarm needs replacing.

How long do CO alarms last?+

It depends on the model. First Alert says most last 5 to 7 years, and some 10-year sealed models last a decade. Kidde alarms start their end-of-life signal about seven years after power-up. Check your manual and the date on the label.

Can I just take the battery out to stop the chirping?+

Only long enough to replace it. An alarm without power can’t warn you about CO.

Need help with hardwired alarms?

If your CO or smoke alarms are hardwired and you’d rather not deal with the chirping, the wiring, or a replacement yourself, Mason can help. See our smoke detector installation and repair page or call (678) 599-8706.